A simple cupboard/enclosure for a hallway

 A friend asked me to build a simple cabinet for them to replace one the was falling apart. They delivered the old cabinet for me to use as a template and I started by doing a simple drawing using Graphic. I've tried Sketchup but never really got on with it for some reason.

Here's the basic idea I developed.

As you can see it's a simple double door cabinet. The challenge was to make it to the same dimensions as the original but because I was using 18mm MDF, the internal dimensions were the critical ones as long as there was space around the outside.

I decided to follow the original as closely as I could because I didn't know what it was covering (some electrical stuff I was told).

The cupboard was only 65mm deep.

I didn't want the rails and stiles on the doors to be too wide because I thought that would make the panel too narrow so I decided on 40mm and that seemed teamwork out okay.

Here's a picture of the cupboard with the doors clamped in place as a test fit before painting.

I think the proportions look okay. 

The next stage was sanding everything down and then preparing it all for painting.

I used a water based primer/undercoat, lightly sanded between coats. The client was doing the final painting, so I did there coats to get it to a reasonable finish. 

Once I was happy with the finish I added the hinges and door knobs. The hinges are simple flush hinges, but that's not the whole story. Initially I went to my local DIY store and got some hinges. Ther problem with them is that they are not that well made and some of the screws do not sit fully into the countersink. In fact so poorly made were these hinges that some of the countersinks barely cut the surface. 

The upshot of which is that the doors don't close properly.

The solution was to buy better quality hinges, sourced from a company specialising in ironmongery. Theres were thicker and far superior quality that the ones from the DIY store.

The inside of the original doors had hooks for keys. This posed a little bit of a problem because the inner panel was only 6mm thick and I had planned to put in some extra pieces into which the hooks could be mounted. Unfortunately 12mm wasn't quite enough to ensure the hooks didn't come through the other side, so I had to add an extra layer. In hindsight I could have designed this better, but I'm not sure how.

The final touch was to add a magnetic catch for each door and the job was done.

The panel doors came out okay. I cut the rebate for them on the table saw rather than setting up the router table. I think next time I'll probably use the router, the table saw was ok but it's a bit fiddly to to get the set-up correct. Still, it worked and the client is happy. 

Simple Storage for the Utility Room

 Our utility room is a mess. We have loads of stuff that needs sorting and the storage is a mixture of old bits of furniture that was in the garage already and shelves that we brought with us or bought to try and make better use of the space. 

The first step was to improve the storage around the washing machine and freezer. This was going to take the shape of some custom made shelves the would store basic item including the cat baskets!

I made this is two parts, a deeper section with two fixed shelves and a shallower version with one fixed shelf and two adjustable shelves (I decided not to have the three I initially put in the drawing). 

In case you're interested the drawing software is Graphic for Mac. It's very useful for creating simple 2D drawings for this sort of project.

The units were built using pocket holes which presented a challenge in the narrow unit because I didn't think about the drill/driver being too big to get inside the unit with the pocket hole driver bit in it. 

I got there in the end, but it was a real faff. The shelf pin holes were made using a Kreg jig. This is a very useful tool. A simple spacer (a piece of ply cut to size) helps to position the jig at its starting point and then you can drill a series of holes equally spaced. If you need more there's a locating pin to reposition the jig. You just need to take your time setting things up properly. I got my jig for about £35.

We've recently bought a battery powered lawn mower so I've attached the charger to the end panel of the unit and the batteries live on the shelf with the charger and battery for the trimmer we were given years ago. This gives us a nice, convenient way to store and charge the batteries.

The next thing we decided to make was a storage unit to fit between the freezer and washing machine.

Nothing too complicated, just a pull-out unit with storage for washing powder, water softener etc. Again pocket holes were used to secure the bottom to the front and back panels, and 30mm brad nails for the rails. 

I found some old castors from a previous project and a handle from a wardrobe I dismantled 8 years ago. The wood from the wardrobe was used to build a cupboard to hide some pipes and to construct one of my benches, so nothing goes to waste if we can help it!

Once finished, the unit slides nicely between the two appliances.

The next job will be to sort out the rest of the storage, making better use of the space. We might even be able to get into the cupboards currently buried behind the stuff we haven't sorted out yet!!